Mich@ł 0 Zgłoś post Napisano Kwiecień 11, 2019 Cześć, Czy bylibyście w stanie pomóc mi w ocenie stanu dysku HDD w moim kimsufi? Serwer jest z 2013 roku i od tej pory pracuje 24/7 głównie jako magazyn na backupy + kilka mniej znaczących stron www. Chciałbym zrobić jego reinstalację i zastanawiam się czy przy okazji nie można by było zrobić jego "konserwacji" aby jeszcze troche podziałał Sprawdzałem smart dysku i coś takiego mi się pokazało: smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.9.120-xxxx-std-ipv6-64] (local bui ld) Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Toshiba 3.5" DT01ACA... Desktop HDD Device Model: TOSHIBA DT01ACA050 Serial Number: 23EMT42PS LU WWN Device Id: 5 000039 ff2f34426 Firmware Version: MS1OA750 User Capacity: 500,107,862,016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Thu Apr 11 16:14:49 2019 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 5225) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off supp ort. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 87) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_ FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0 2 Throughput_Performance 0x0005 133 133 054 Pre-fail Offline - 104 3 Spin_Up_Time 0x0007 131 131 024 Pre-fail Always - 175 (Average 175) 4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 58 5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 118 118 020 Pre-fail Offline - 33 9 Power_On_Hours 0x0012 093 093 000 Old_age Always - 49781 10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 58 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 104 193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 104 194 Temperature_Celsius 0x0002 222 222 000 Old_age Always - 27 (Min/Max 21/42) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0 SMART Error Log Version: 1 ATA Error Count: 7290 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 7290 occurred at disk power-on lifetime: 34285 hours (1428 days + 13 hours ) When the command that caused the error occurred, the device was active or idle . After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 08 48 f8 09 Error: UNC at LBA = 0x09f84808 = 167266312 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 08 b0 08 48 f8 40 00 00:03:54.252 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 00:03:54.252 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 e0 00 00:03:54.252 READ NATIVE MAX ADDRESS EXT [OBS-AC S-3] ec 00 00 00 00 00 a0 00 00:03:54.251 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 00:03:54.251 SET FEATURES [Set transfer mode] Error 7289 occurred at disk power-on lifetime: 34285 hours (1428 days + 13 hours ) When the command that caused the error occurred, the device was active or idle . After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 08 48 f8 09 Error: UNC at LBA = 0x09f84808 = 167266312 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 08 20 08 48 f8 40 00 00:03:50.458 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 00:03:50.458 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 e0 00 00:03:50.458 READ NATIVE MAX ADDRESS EXT [OBS-AC S-3] ec 00 00 00 00 00 a0 00 00:03:50.457 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 00:03:50.457 SET FEATURES [Set transfer mode] Error 7288 occurred at disk power-on lifetime: 34285 hours (1428 days + 13 hours ) When the command that caused the error occurred, the device was active or idle . After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 08 48 f8 09 Error: UNC at LBA = 0x09f84808 = 167266312 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 08 90 08 48 f8 40 00 00:03:46.742 READ FPDMA QUEUED 60 08 88 00 48 f8 40 00 00:03:46.737 READ FPDMA QUEUED 60 08 80 f0 3f 38 40 00 00:03:46.736 READ FPDMA QUEUED 60 08 70 80 3f 38 40 00 00:03:46.723 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 00:03:46.718 SET FEATURES [Enable SATA feature] Error 7287 occurred at disk power-on lifetime: 34285 hours (1428 days + 13 hours ) When the command that caused the error occurred, the device was active or idle . After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 08 48 f8 09 Error: UNC at LBA = 0x09f84808 = 167266312 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 08 d8 08 48 f8 40 00 00:03:42.077 READ FPDMA QUEUED 60 40 d0 20 48 f8 40 00 00:03:42.077 READ FPDMA QUEUED 60 08 b8 00 48 f8 40 00 00:03:42.061 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 00:03:42.060 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 e0 00 00:03:42.060 READ NATIVE MAX ADDRESS EXT [OBS-AC S-3] Error 7286 occurred at disk power-on lifetime: 34285 hours (1428 days + 13 hours ) When the command that caused the error occurred, the device was active or idle . After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 18 08 48 f8 09 Error: UNC at LBA = 0x09f84808 = 167266312 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 20 30 00 48 f8 40 00 00:03:38.271 READ FPDMA QUEUED 60 08 28 f0 3f 38 40 00 00:03:38.271 READ FPDMA QUEUED 60 08 18 80 3f 38 40 00 00:03:38.261 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 00:03:38.252 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 e0 00 00:03:38.251 READ NATIVE MAX ADDRESS EXT [OBS-AC S-3] SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA _of_first_error # 1 Short offline Completed without error 00% 22 - # 2 Short offline Completed without error 00% 17 - # 3 Short offline Completed without error 00% 17 - # 4 Short offline Completed without error 00% 4 - # 5 Short offline Completed without error 00% 3 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. Udostępnij ten post Link to postu Udostępnij na innych stronach
greg1 0 Zgłoś post Napisano Kwiecień 8, 2020 na moje oko 5 realokowanych sekorów, do wymiany nie warto ryzykować Udostępnij ten post Link to postu Udostępnij na innych stronach
