Skocz do zawartości
Zaloguj się, aby obserwować  
Obserwujący 0
Dareksbs

Odczyt SMART

Przez Dareksbs, w Sprzęt serwerowy i Centrum Danych

Polecane posty

Dareksbs    0

Dareksbs
Napisano

Cześć,

 

Mógłby ktoś mi powiedzieć jak się maja moje dyski ?

 

Pierwszy :

Parameter Value Threshold Worst
---------------------------- ----- --------- -----
Health Status OK N/A N/A
Media Wearout Indicator N/A N/A N/A
Write Error Count N/A N/A N/A
Read Error Count 100 16 100
Power-on Hours 99 0 99
Power Cycle Count 100 0 100
Reallocated Sector Count 100 5 100
Raw Read Error Rate 100 16 100
Drive Temperature 222 0 222
Driver Rated Max Temperature N/A N/A N/A
Write Sectors TOT Count 200 0 200
Read Sectors TOT Count N/A N/A N/A
Initial Bad Block Count N/A N/A N/A

 

Drugi :
Parameter Value Threshold Worst
---------------------------- ----- --------- -----
Health Status OK N/A N/A
Media Wearout Indicator N/A N/A N/A
Write Error Count N/A N/A N/A
Read Error Count 100 16 100
Power-on Hours 99 0 99
Power Cycle Count 100 0 100
Reallocated Sector Count 100 5 100
Raw Read Error Rate 100 16 100
Drive Temperature 214 0 214
Driver Rated Max Temperature N/A N/A N/A
Write Sectors TOT Count 200 0 200
Read Sectors TOT Count N/A N/A N/A
Initial Bad Block Count N/A N/A N/A

 

Dziękuje

Udostępnij ten post

Link to postu
Udostępnij na innych stronach

Pan Kot    1535

Pan Kot
Napisano

Zawrzyj jakieś RAW wartości bo z tego wyżej jedyna odpowiedź jaką można dać to "jest ok".

 

 

root@archi:~# smartctl -a /dev/sda

smartctl 6.4 2014-10-07 r4002 [x86_64-linux-3.17.4-grsec-archi-ovh-edition] (loc al build)
Copyright © 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Toshiba 3.5" HDD DT01ACA...
Device Model: TOSHIBA DT01ACA050
Serial Number: 23EMLTNPS
LU WWN Device Id: 5 000039 ff2f3301e
Firmware Version: MS1OA750
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Tue Dec 2 07:06:23 2014 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 5063) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off supp ort.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 85) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_ FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0
2 Throughput_Performance 0x0005 136 136 054 Pre-fail Offline - 92
3 Spin_Up_Time 0x0007 123 123 024 Pre-fail Always - 186 (Average 185)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 22
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 113 113 020 Pre-fail Offline - 35
9 Power_On_Hours 0x0012 099 099 000 Old_age Always - 11575
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 22
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 63
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 63
194 Temperature_Celsius 0x0002 187 187 000 Old_age Always - 32 (Min/Max 25/42)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA _of_first_error
# 1 Short offline Completed without error 00% 20 -
# 2 Short offline Completed without error 00% 16 -
# 3 Short offline Completed without error 00% 15 -
# 4 Short offline Completed without error 00% 4 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
root@archi:~# smartctl -a /dev/sda
smartctl 6.4 2014-10-07 r4002 [x86_64-linux-3.17.4-grsec-archi-ovh-edition] (local build)
Copyright © 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Toshiba 3.5" HDD DT01ACA...
Device Model: TOSHIBA DT01ACA050
Serial Number: 23EMLTNPS
LU WWN Device Id: 5 000039 ff2f3301e
Firmware Version: MS1OA750
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Tue Dec 2 07:06:26 2014 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 5063) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 85) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0
2 Throughput_Performance 0x0005 136 136 054 Pre-fail Offline - 92
3 Spin_Up_Time 0x0007 123 123 024 Pre-fail Always - 186 (Average 185)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 22
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 113 113 020 Pre-fail Offline - 35
9 Power_On_Hours 0x0012 099 099 000 Old_age Always - 11575
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 22
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 63
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 63
194 Temperature_Celsius 0x0002 187 187 000 Old_age Always - 32 (Min/Max 25/42)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 20 -
# 2 Short offline Completed without error 00% 16 -
# 3 Short offline Completed without error 00% 15 -
# 4 Short offline Completed without error 00% 4 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

Masz, tak powinien smart wyglądać ;).

Udostępnij ten post

Link to postu
Udostępnij na innych stronach

ritchey    91

ritchey
Napisano

Normalnie np. w Intelach SSD kluczowym parametrem jest "Media Wearout Indicator" którego wartość dla nowego dysku wynosi 100 i z czasem się zmniejsza. Gdy zbliża się do zera to oznacza że musisz wymienić dysk na nowy gdyż jego komórki wyczerpały już maksymalną ilość swoich cykli życia.

Tylko że w twoich dyskach "Media Wearout Indicator" jest jako N/A - stąd wynika że to nie są dyski SSD.

Generalnie z danych które przesłałeś - prawie wszystkie kluczowe parametry (dot. błędów) mają wartość 100 - co oznacza bezbłędną pracę. Tak samo "Health Status: OK". Dokładny opis poszczególnych parametrów SMART masz tutaj:

 

http://en.wikipedia.org/wiki/S.M.A.R.T.#ATA_S.M.A.R.T._attributes

Udostępnij ten post

Link to postu
Udostępnij na innych stronach

Bądź aktywny! Zaloguj się lub utwórz konto

Tylko zarejestrowani użytkownicy mogą komentować zawartość tej strony

Utwórz konto

Zarejestruj nowe konto, to proste!

Zarejestruj nowe konto

Zaloguj się

Posiadasz własne konto? Użyj go!

Zaloguj się
Zaloguj się, aby obserwować  
Obserwujący 0
Przejdź do listy tematów Sprzęt serwerowy i Centrum Danych
×