jasne 0 Zgłoś post Napisano Czerwiec 29, 2014 Witam otrzymuje takie błędy.. ze smartctl, o co chodzi? === START OF INFORMATION SECTION === Device Model: ST3750528AS Serial Number: 9VP7TBE0 Firmware Version: CC46 User Capacity: 750,156,374,016 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 4 Local Time is: Sun Jun 29 11:37:58 2014 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 634) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 152) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103f) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 115 099 006 Pre-fail Always - 86626821 3 Spin_Up_Time 0x0003 095 095 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 30 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 084 060 030 Pre-fail Always - 9224749270 9 Power_On_Hours 0x0032 087 087 000 Old_age Always - 11629 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 15 183 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0 184 Unknown_Attribute 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 098 098 000 Old_age Always - 2 188 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0 189 High_Fly_Writes 0x003a 099 099 000 Old_age Always - 1 190 Airflow_Temperature_Cel 0x0022 063 048 045 Old_age Always - 37 (Lifetime Min/Max 33/47) 194 Temperature_Celsius 0x0022 037 052 000 Old_age Always - 37 (0 18 0 0) 195 Hardware_ECC_Recovered 0x001a 041 034 000 Old_age Always - 86626821 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 5 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 5 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 47266115104144 241 Unknown_Attribute 0x0000 100 253 000 Old_age Offline - 2003774967 242 Unknown_Attribute 0x0000 100 253 000 Old_age Offline - 2788371689 SMART Error Log Version: 1 ATA Error Count: 2 CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2 occurred at disk power-on lifetime: 11166 hours (465 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 ff ff ff ef 00 48d+22:39:31.836 READ DMA EXT ca 00 08 37 74 37 e1 00 48d+22:39:31.835 WRITE DMA ea 00 00 ff ff ff af 00 48d+22:39:31.807 FLUSH CACHE EXIT 25 00 08 ff ff ff ef 00 48d+22:39:31.807 READ DMA EXT ca 00 38 ff 73 37 e1 00 48d+22:39:31.807 WRITE DMA Error 1 occurred at disk power-on lifetime: 11166 hours (465 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 e0 ff ff ff ef 00 48d+22:39:28.759 READ DMA EXT 25 00 68 ff ff ff ef 00 48d+22:39:28.758 READ DMA EXT 25 00 a8 ff ff ff ef 00 48d+22:39:28.731 READ DMA EXT 25 00 90 ff ff ff ef 00 48d+22:39:28.715 READ DMA EXT 25 00 68 ff ff ff ef 00 48d+22:39:28.714 READ DMA EXT SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute Udostępnij ten post Link to postu Udostępnij na innych stronach
Miłosz 2311 Zgłoś post Napisano Czerwiec 29, 2014 Czas już przyszedł na ten dysk. Backupuj na bieżąco i wymieniaj go. Udostępnij ten post Link to postu Udostępnij na innych stronach
