Skocz do zawartości
Gość Marshall

[EXIM]kodowanie na iso-8859-2

Polecane posty

Gość Marshall

Witam

Mam kłopot z eximem na moim serwerze , przy próbie wysłania mailingu z panelu directadmin odbiorca otrzymuje krzaki zamiast wiadomości

 

Mój konfig z exima co trzeba zmienić aby normalnie on wysyłał wiadomości proszę o pomoc

 

###################################################################### #                 SpamBlocker.exim.conf.2.1.1-release                # #                             05-Jun-2007                            # #   Runtime configuration file for DirectAdmin/Exim 4.24 and above   # #          Requires exim.pl dated 20-Apr-2007 17:09 or later         # ######### IMPORTANT ########## IMPORTANT ########## IMPORTANT ######## # WARNING! Be sure to back up your previous exim.conf file before    # # attempting to use this exim.conf file.                             # #                                                                    # # Do may not use this exim.conf Exim configuration file unless you   # # make the required modifications to your Exim configuration         # # following the instructions in the README file included in this     # # distribution.                                                      # #                                                                    # # This is version "2.0 of the SpamBlocker exim.conf file as          # # distributed by NoBaloney Internet Services for DirectAdmin based   # # servers.                                                           # #                                                                    # # More information about NoBaloney.net may be found at:              # #  http://www.nobaloney.net/                                         # #                                                                    # # More information about DirectAdmin may be found at:                # #  http://www.directadmin.com/                                       # #                                                                    # # This Exim configuration file has been modified from the original   # # as distributed with Exim 4.  The modifications have been made by:  # #                                                                    # # Jeff Lasman                                                        # # NoBaloney Internet Services                                        # # Post Office Box 52200                                              # # Riverside, CA 92517-3200                                           # # spamblocker@nobaloney.net                                          # # (951) 643-5345                                                     # #                                                                    # # The SpamBlocker exim.conf file has been modified from the original # # exim.conf file as distributed with Exim 4, which includes the      # # following copyright notice:                                        # #                                                                    # # Copyright (C) 2002 University of Cambridge, Cambridge, UK          # #                                                                    # # Portions of the file are taken from the exim.conf file as          # # distributed with DirectAdmin (http://www.directadmin.com/),        # #                                                                    # # Copyright(C)2003-2007 JBMC Software, St Albert, AB, Canada T8N 5C9 # #                                                                    # # Portions of this file are written by Jeff Lasman, of               # # NoBaloney Internet Services and are copyright as follows:          # #                                                                    # # Copyright (C) 2004-2007 NoBaloney Internet Services,               # # Riverside, Calif., USA                                             # #                                                                    # # The entire Exim 4 distribution, including the exim.conf file, is   # # distributed under the GNU GENERAL PUBLIC LICENSE, Version 2,       # # June 1991. If you do not have a copy of the GNU GENERAL            # # PUBLIC LICENSE you may download it, in it's entirety, from         # # the website at:                                                    # #                                                                    # # http://www.nobaloney.net/exim/gnu-gpl-v2.txt                       # #                                                                    # ###################################################################### #                                                                    # # The most recent version of this SpamBlocker exim.conf file may     # # always be downloaded from the website at                           # #                                                                    # # http://www.nobaloney.net/exim/exim.conf.spamblocked                # #                                                                    # ######### IMPORTANT ########## IMPORTANT ########## IMPORTANT ######## #                                                                    # # Whenever you change Exim's configuration file, you *must* remember # # to HUP the Exim daemon, because it will not pick up the new        # # configuration until you do. However, any other Exim processes that # # are started, for example, a process started by an MUA in order to  # # send a message, will see the new configuration as soon as it is in # # place.                                                             # #                                                                    # # You do not need to HUP the daemon for changes in auxiliary files   # # that are referenced from this file. They are read every time they  # # are used.                                                          # #                                                                    # # It is usually a good idea to test a new configuration for          # # syntactic correctness before installing it (for example, by        # # running the command "exim -C /config/file.new -bV").               # #                                                                    # ### MODIFICATION INSTRUCTIONS ########## MODIFICATION INSTRUCTIONS ### #                                                                    # # YOU MUST MAKE THE CHANGES TO THIS SpamBlocked exim.conf file as    # # documented in the README file.                                     # #                                                                    # # The README file for this version is named:                         # # README.SpamBlocker.exim.conf.2.1                                   # #                                                                    # ###################################################################### #   update information: changed blockists 29-May-2007 version 2.1    # ######################################################################  # Specify your host's canonical name here. This should normally be the # fully qualified "official" name of your host. If this option is not # set, the uname() function is called to obtain the name. In many cases # this does the right thing and you need not set anything explicitly.  # primary_hostname =  # Specify the domain you want to be added to all unqualified addresses # here. An unqualified address is one that does not contain an "@" character # followed by a domain. For example, "caesar@rome.ex" is a fully qualified # address, but the string "caesar" (i.e. just a login name) is an unqualified # email address. Unqualified addresses are accepted only from local callers by # default. See the receiver_unqualified_{hosts,nets} options if you want # to permit unqualified addresses from remote sources. If this option is # not set, the primary_hostname value is used for qualification.  # qualify_domain =  # If you want unqualified recipient addresses to be qualified with a different # domain to unqualified sender addresses, specify the recipient domain here. # If this option is not set, the qualify_domain value is used.  # qualify_recipient =  # the next line is required to start the smtp auth script included # in DirectAdmin  perl_startup = do '/etc/exim.pl'  # the next line is required to start the system_filter included in # DirectAdmin to refuse potentiallly harmful payloads in # email messages  system_filter = /etc/system_filter.exim  # next line to allow incoming email submission port 587 # see also check_recipient second ruleset  daemon_smtp_ports = 25 : 587  # SET SOME MEANINGFUL LIMITS # OPTIONAL MODIFICATIONS: #  These defaults work for us; you may wish to modify them #  for your environment  message_size_limit = 20M smtp_receive_timeout = 5m smtp_accept_max = 100 message_body_visible = 3000 print_topbitchars = true deliver_queue_load_max = 5 smtp_connect_backlog = 50 split_spool_directory = yes  # ALLOW UNDERSCORE IN EMAIL DOMAIN NAME # domains shouldn't use the underscore character "_" but some # may.  Because John Postel, one of the architects of the Internet, # said "Be liberal in what you accept and conservative in what you # transmit, we choose to allow underscore in email domain names so we # can receive email form domains which use the underscore character # in their domain name. # OPTIONAL MODIFICATIONS: #  These defaults work for us; you may wish to modify them #  for your environment  helo_allow_chars = _  # CHANGE LOGGING BEHAVIOR # We weren't happy with the default Exim logging behavior through # syslog; it didn't give us enough information.  So we turned off # syslog behavior and changed the logging behavior to give us what we # felt was more helpful information.  You may choose to delete or modify # this section. # OPTIONAL MODIFICATIONS: #  These defaults work for us; you may wish to modify them #  for your environment  log_selector = \   +delivery_size \   +sender_on_delivery \   +received_recipients \   +received_sender \   +smtp_confirmation \   +subject \   +smtp_incomplete_transaction \   -dnslist_defer \   -host_lookup_failed \   -queue_run \   -rejected_header \   -retry_defer \   -skip_delivery  syslog_duplication = false  # These options specify the Access Control Lists (ACLs) that # are used for incoming SMTP messages - after the RCPT and DATA # commands, respectively.  acl_smtp_rcpt = check_recipient acl_smtp_data = check_message  # define local lists  addresslist whitelist_senders = lsearch;/etc/virtual/whitelist_senders addresslist blacklist_senders = lsearch;/etc/virtual/blacklist_senders domainlist blacklist_domains = lsearch;/etc/virtual/blacklist_domains domainlist whitelist_domains = lsearch;/etc/virtual/whitelist_domains domainlist local_domains = lsearch;/etc/virtual/domains domainlist relay_domains = lsearch;/etc/virtual/domains : localhost domainlist use_rbl_domains = lsearch;/etc/virtual/use_rbl_domains hostlist auth_relay_hosts = * hostlist bad_sender_hosts = lsearch;/etc/virtual/bad_sender_hosts hostlist bad_sender_hosts_ip = net-lsearch;/etc/virtual/bad_sender_hosts hostlist relay_hosts = net-lsearch;/etc/virtual/pophosts hostlist whitelist_hosts = lsearch;/etc/virtual/whitelist_hosts hostlist whitelist_hosts_ip = net-lsearch;/etc/virtual/whitelist_hosts  # If you want to accept mail addressed to your host's literal IP address, for # example, mail addressed to "user@[111.111.111.111]", then uncomment the # following line, or supply the literal domain(s) as part of "local_domains" # above. You also need to comment "forbid_domain_literals" below. This is not # recommended for today's Internet.  # DO NOT ALLOW HOST LITERALS # OPTIONAL MODIFICATIONS: #  These defaults work for us; you may wish to uncomment the line  #  below and change the allow_domain_literals line below to true #  to allow domain literals in your environment  # local_domains_include_host_literals  # The following line prevents Exim from recognizing addresses of the form # "user@[111.111.111.111]" that is, with a "domain literal" (an IP address) # instead of a named domain. The RFCs still require this form, but it makes # little sense to permit mail to be sent to specific hosts by their IP address # in the modern Internet, and this ancient format has been used by those # seeking to abuse hosts by using them for unwanted relaying. If you really # do want to support domain literals, remove the following line, and see # also the "domain_literal" router below.  allow_domain_literals = false  # No local deliveries will ever be run under the uids of these users (a colon- # separated list). An attempt to do so gets changed so that it runs under the # uid of "nobody" instead. This is a paranoic safety catch. Note the default # setting means you cannot deliver mail addressed to root as if it were a # normal user. This isn't usually a problem, as most sites have an alias for # root that redirects such mail to a human administrator.  never_users = root  # DO HOST LOOKUP # OPTIONAL MODIFICATIONS: # The setting below causes Exim to do a reverse DNS lookup on all incoming # IP calls, in order to get the true host name. If you feel this is too # expensive, you can specify the networks for which a lookup is done, or # remove the setting entirely.  host_lookup = *  # DISALLOW IDENT CALLBACKS # OPTIONAL MODIFICATIONS: # Exim may be set to make RFC 1413 (ident) callbacks for all incoming SMTP # calls. You can limit the hosts to which these calls are made, and/or change # the timeout that is used. If you set the timeout to zero, all RFC 1413 calls # are disabled. RFC 1413 calls are cheap and can provide useful information # for tracing problem messages, but some hosts and firewalls have problems # with them. This can result in a timeout instead of an immediate refused # connection, leading to delays on starting up an SMTP session.  By default # we disable callbacks for incoming SMTP calls.  You may change # rfc1413_query_timeout to 30s or some other positive number of seconds to # enable callbacks for incoming SMTP calls.  rfc1413_hosts = * rfc1413_query_timeout = 0s  # BOUNCE MESSAGES # OPTIONAL MODIFICATIONS: # When Exim can neither deliver a message nor return it to sender, it # "freezes" the delivery error message (aka "bounce message"). There are also # other circumstances in which messages get frozen. They will stay on the # queue forever unless one or both of the following options is set.  # This option unfreezes bounce messages after two days, tries # once more to deliver them, and ignores any delivery failures.  ignore_bounce_errors_after = 2d  # This option cancels (removes) frozen messages that are older than five days.  timeout_frozen_after = 5d  # TRUSTED USERS # OPTIONAL MODIFICATIONS: # if you must add additional trusted users, do so here; continue the # colon-delimited list  trusted_users = mail:majordomo:apache:diradmin  # SSL/TLS cert and key tls_certificate = /etc/exim.cert tls_privatekey = /etc/exim.key tls_require_ciphers = ALL:!ADH:RC4+RSA:+HIGH:+MEDIUM:-LOW:-SSLv2:-EXP tls_advertise_hosts = * #auth_over_tls_hosts = *  ###################################################################### #                               ACLs                                 # ######################################################################  begin acl  # ACL that is used after the RCPT command check_recipient:  # to block certain wellknown exploits, Deny for local domains if # local parts begin with a dot or contain @ % ! / |   deny  domains       = +local_domains         local_parts   = ^[.] : ^.*[@%!/|]  # to restrict port 587 to authenticated users only # see also daemon_smtp_ports above accept  hosts = +auth_relay_hosts         condition = ${if eq {$interface_port}{587} {yes}{no}}         endpass         message = relay not permitted, authentication required         authenticated = *  # allow local users to send outgoing messages using slashes # and vertical bars in their local parts. # Block outgoing local parts that begin with a dot, slash, or vertical # bar but allows them within the local part. # The sequence \..\ is barred. The usage of @ % and ! is barred as # before. The motivation is to prevent your users (or their virii) # from mounting certain kinds of attacks on remote sites.   deny  domains       = !+local_domains         local_parts   = ^[./|] : ^.*[@%!] : ^.*/\\.\\./  # local source whitelist # accept if the source is local SMTP (i.e. not over TCP/IP). # Test for this by testing for an empty sending host field.   accept  hosts = :  # sender domains whitelist # accept if sender domain is in whitelist   accept  sender_domains = +whitelist_domains  # sender hosts whitelist # accept if sender host is in whitelist   accept  hosts = +whitelist_hosts   accept  hosts = +whitelist_hosts_ip  # envelope senders whitelist # accept if envelope sender is in whitelist   accept  senders = +whitelist_senders  # accept mail to postmaster in any local domain, regardless of source   accept  local_parts = postmaster           domains     = +local_domains  # accept mail to abuse in any local domain, regardless of source   accept  local_parts = abuse           domains     = +local_domains  # accept mail to hostmaster in any local domain, regardless of source   accept  local_parts = hostmaster           domains     =+local_domains  # OPTIONAL MODIFICATIONS: # If the page you're using to notify senders of blocked email of how # to get their address unblocked will use a web form to send you email so # you'll know to unblock those senders, then you may leave these lines # commented out.  However, if you'll be telling your senders of blocked # email to send an email to errors@yourdomain.com, then you should # replace "errors" with the left side of the email address you'll be # using, and "example.com" with the right side of the email address and # then uncomment the second two lines, leaving the first one commented. # Doing this will mean anyone can send email to this specific address, # even if they're at a blocked domain, and even if your domain is using # blocklists.  # accept mail to errors@example.com, regardless of source #   accept  local_parts = errors #           domains     = example.com  # deny so-called "legal" spammers"   deny message = Email blocked by LBL - to unblock see http://www.example.com/        # only for domains that do want to be tested against RBLs        domains = +use_rbl_domains        sender_domains = +blacklist_domains  # deny using hostname in bad_sender_hosts blacklist   deny message = Email blocked by BSHL - to unblock see http://www.example.com/        # only for domains that do want to be tested against RBLs        domains = +use_rbl_domains        hosts = +bad_sender_hosts  # deny using IP in bad_sender_hosts blacklist   deny message = Email blocked by BSHL - to unblock see http://www.example.com/        # only for domains that do want to be tested against RBLs        domains = +use_rbl_domains        hosts = +bad_sender_hosts_ip  # deny using email address in blacklist_senders   deny message = Email blocked by BSAL - to unblock see http://www.example.com/   domains = use_rbl_domains   deny senders = +blacklist_senders  # By default we do NOT require sender verification. # Sender verification denies unless sender address can be verified: # If you want to require sender verification, i.e., that the sending # address is routable and mail can be delivered to it, then # uncomment the next line. If you do not want to require sender # verification, leave the line commented out  #require verify = sender  # deny using spamhaus   deny message = Email blocked by SPAMHAUS - to unblock see http://www.example.com/        # only for domains that do want to be tested against RBLs         hosts = !+relay_hosts        domains = +use_rbl_domains        !authenticated = *        dnslists = zen.spamhaus.org  # deny using njabl   deny message = Email blocked by NJABL - to unblock see http://www.example.com/        hosts = !+relay_hosts        domains = +use_rbl_domains        !authenticated = *        dnslists = dnsbl.njabl.org  # deny using cbl #  deny message = Email blocked by CBL - to unblock see http://www.example.com/ #       hosts = !+relay_hosts #       domains = +use_rbl_domains #       !authenticated = * #       dnslists = cbl.abuseat.org  ## deny using sorbs name based list #  deny message = Email blocked by SORBS - to unblock see http://www.example.com/ #       domains =+use_rbl_domains #       # rhsbl list is name based #       dnslists = rhsbl.sorbs.net/$sender_address_domain  # accept if address is in a local domain as long as recipient can be verified   accept  domains = +local_domains           endpass 	  message = "Unknown User"           verify = recipient  # accept if address is in a domain for which we relay as long as recipient # can be verified   accept  domains = +relay_domains           endpass           verify=recipient  # accept if message comes for a host for which we are an outgoing relay # recipient verification is omitted because many MUA clients don't cope # well with SMTP error responses. If you are actually relaying from MTAs # then you should probably add recipient verify here    accept  hosts = +relay_hosts   accept  hosts = +auth_relay_hosts           endpass           message = authentication required           authenticated = *   deny    message = relay not permitted  # default at end of acl causes a "deny", but line below will give # an explicit error message:   deny    message = relay not permitted  # ACL that is used after the DATA command check_message:   accept  ###################################################################### #                   AUTHENTICATION CONFIGURATION                     # ######################################################################  # There are no authenticator specifications in this default configuration file.  begin authenticators  plain:     driver = plaintext     public_name = PLAIN     server_prompts = :     server_condition = "${perl{smtpauth}}"     server_set_id = $2  login:     driver = plaintext     public_name = LOGIN     server_prompts = "Username:: : Password::"     server_condition = "${perl{smtpauth}}"     server_set_id = $1   ###################################################################### #                      REWRITE CONFIGURATION                         # ######################################################################  # There are no rewriting specifications in this default configuration file.  ###################################################################### #                      ROUTERS CONFIGURATION                         # #            Specifies how remote addresses are handled              # ###################################################################### #                          ORDER DOES MATTER                         # #  A remote address is passed to each in turn until it is accepted.  # ######################################################################  begin routers  # Remote addresses are those with a domain that does not match any item # in the "local_domains" setting above.  # This router routes to remote hosts over SMTP using a DNS lookup. Any domain # that resolves to an IP address on the loopback interface (127.0.0.0/8) is # treated as if it had no DNS entry.  lookuphost:   driver = dnslookup   domains = ! +local_domains   ignore_target_hosts = 127.0.0.0/8   condition = "${perl{check_limits}}"   transport = remote_smtp   no_more  # This router routes to remote hosts over SMTP by explicit IP address, # when an email address is given in "domain literal" form, for example, # <user@[192.168.35.64]>. The RFCs require this facility. However, it is # little-known these days, and has been exploited by evil people seeking # to abuse SMTP relays. Consequently it is commented out in the default # configuration. If you uncomment this router, you also need to comment out # "forbid_domain_literals" above, so that Exim can recognize the syntax of # domain literal addresses.  # domain_literal: #   driver = ipliteral #   transport = remote_smtp  ###################################################################### #                      DIRECTORS CONFIGURATION                       # #             Specifies how local addresses are handled              # ###################################################################### #                          ORDER DOES MATTER                         # #   A local address is passed to each in turn until it is accepted.  # ######################################################################  # Local addresses are those with a domain that matches some item in the # "local_domains" setting above, or those which are passed back from the # routers because of a "self=local" setting (not used in this configuration).  #.include_if_exists /etc/exim.spamassassin.conf  # Spam Assassin #spamcheck_director: #  driver = accept #  condition = "${if and { \ #			{!def:h_X-Spam-Flag:} \ #			{!eq {$received_protocol}{spam-scanned}} \ #			{!eq {$received_protocol}{local}} \ #			{exists{/home/${lookup{$domain}lsearch{/etc/virtual/domainowners}{$value}}/.spamassassin/user_prefs}} \ #			{<{$message_size}{500k}} \ #		} {1}{0}}" #  retry_use_local_part #  transport = spamcheck #  no_verify  majordomo_aliases:   driver = redirect   allow_defer   allow_fail   data = ${if exists{/etc/virtual/${domain}/majordomo/list.aliases}{${lookup{$local_part}lsearch{/etc/virtual/${domain}/majordomo/list.aliases}}}}   domains = lsearch;/etc/virtual/domainowners   file_transport = address_file   group = daemon   pipe_transport = majordomo_pipe   retry_use_local_part   no_rewrite   user = majordomo  majordomo_private:   driver = redirect   allow_defer   allow_fail   #condition = "${if eq {$received_protocol} {local} {true} {false} }"   condition = "${if or { {eq {$received_protocol} {local}} \                          {eq {$received_protocol} {spam-scanned}} } {true} {false} }"   data = ${if exists{/etc/virtual/${domain}/majordomo/private.aliases}{${lookup{$local_part}lsearch{/etc/virtual/${domain}/majordomo/private.aliases}}}}   domains = lsearch;/etc/virtual/domainowners   file_transport = address_file   group = daemon   pipe_transport = majordomo_pipe   retry_use_local_part   user = majordomo  domain_filter:   driver = redirect   allow_filter   no_check_local_user   condition = "${if exists{/etc/virtual/${domain}/filter}{yes}{no}}"   user = "mail"   file = /etc/virtual/${domain}/filter   file_transport = address_file   pipe_transport = virtual_address_pipe   retry_use_local_part   no_verify  uservacation:    driver = accept    condition = ${lookup{$local_part} lsearch {/etc/virtual/${domain}/vacation.conf}{yes}{no}}    require_files = /etc/virtual/${domain}/reply/${local_part}.msg    transport = uservacation    unseen  userautoreply:    driver = accept    condition = ${lookup{$local_part} lsearch {/etc/virtual/${domain}/autoresponder.conf}{yes}{no}}    require_files = /etc/virtual/${domain}/reply/${local_part}.msg    transport = userautoreply    unseen  virtual_aliases_nostar:   driver = redirect   allow_defer   allow_fail   data = ${if exists{/etc/virtual/${domain}/aliases}{${lookup{$local_part}lsearch{/etc/virtual/${domain}/aliases}}}}   file_transport = address_file   group = mail   pipe_transport = virtual_address_pipe   retry_use_local_part   unseen   #include_domain = true  virtual_user:   driver = accept   #condition = ${if eq {}{${if exists{/etc/virtual/${domain}/passwd}{${lookup{$local_part}lsearch{/etc/virtual/${domain}/passwd}}}}}{no}{yes}}   condition = ${perl{save_virtual_user}}   domains = lsearch;/etc/virtual/domainowners   group = mail   retry_use_local_part   transport = virtual_localdelivery  virtual_aliases:   driver = redirect   allow_defer   allow_fail   condition = ${if eq {}{${if exists{/etc/virtual/${domain}/aliases}{${lookup{$local_part}lsearch{/etc/virtual/${domain}/aliases}}}}}{yes}{no}}   data = ${if exists{/etc/virtual/$domain/aliases}{${lookup{$local_part}lsearch*{/etc/virtual/$domain/aliases}}}}   file_transport = address_file   group = mail   pipe_transport = virtual_address_pipe   retry_use_local_part   #include_domain = true  #if we have an alias, but no passwd entry we have to drop the email because the #first alias is unseen (so that you can forward as well as save it) #The save part is "seen" (virtual_user), but the forward before it isn't.  This #will be the spot where we "see" the email so that it doesn't send a bounce if #we have an alias but no pop. drop_solo_alias:   driver = redirect   allow_defer   allow_fail   data = ${if exists{/etc/virtual/$domain/aliases}{${lookup{$local_part}lsearch{/etc/virtual/$domain/aliases}}}}   file_transport = devnull   group = mail   #pipe_transport = virtual_address_pipe   pipe_transport = devnull   retry_use_local_part   #include_domain = true   # This director handles forwarding using traditional .forward files. # If you want it also to allow mail filtering when a forward file # starts with the string "# Exim filter", uncomment the "filter" option. # The check_ancestor option means that if the forward file generates an # address that is an ancestor of the current one, the current one gets # passed on instead. This covers the case where A is aliased to B and B # has a .forward file pointing to A. The three transports specified at the # end are those that are used when forwarding generates a direct delivery # to a file, or to a pipe, or sets up an auto-reply, respectively.  userforward:   driver = redirect   allow_filter   check_ancestor   check_local_user   no_expn   file = $home/.forward   file_transport = address_file   pipe_transport = address_pipe   reply_transport = address_reply   no_verify  system_aliases:   driver = redirect   allow_defer   allow_fail   data = ${lookup{$local_part}lsearch{/etc/aliases}}   file_transport = address_file   pipe_transport = address_pipe   retry_use_local_part   # user = exim  localuser:   driver = accept   check_local_user   condition = "${if eq {$domain} {$primary_hostname} {yes} {no}}"   transport = local_delivery  # This director matches local user mailboxes.  ###################################################################### #                      TRANSPORTS CONFIGURATION                      # ###################################################################### #                       ORDER DOES NOT MATTER                        # #     Only one appropriate transport is called for each delivery.    # ######################################################################  # A transport is used only when referenced from a director or a router that # successfully handles an address.   # Spam Assassin begin transports  spamcheck:   driver = pipe   batch_max = 100   command = /usr/sbin/exim -oMr spam-scanned -bS   current_directory = "/tmp"   group = mail   home_directory = "/tmp"   log_output   message_prefix =    message_suffix =    return_fail_output   no_return_path_add   transport_filter = /usr/bin/spamc -u ${lookup{$domain}lsearch*{/etc/virtual/domainowners}{$value}}   use_bsmtp   user = mail   # must use a privileged user to set $received_protocol on the way back in!   #majordomo majordomo_pipe:   driver = pipe   group = daemon   return_fail_output   user = majordomo  # This transport is used for local delivery to user mailboxes in traditional # BSD mailbox format. By default it will be run under the uid and gid of the # local user, and requires the sticky bit to be set on the /var/mail directory. # Some systems use the alternative approach of running mail deliveries under a # particular group instead of using the sticky bit. The commented options below # show how this can be done.  local_delivery:   driver = appendfile   delivery_date_add   envelope_to_add   file = /var/mail/$local_part   group = mail   mode = 0660   return_path_add   user = ${local_part}  ## for delivering virtual domains to their own mail spool  virtual_localdelivery:   driver = appendfile   create_directory   delivery_date_add   directory_mode = 700   envelope_to_add   file = /var/spool/virtual/${domain}/${local_part}   group = mail   mode = 660   return_path_add   user = "${lookup{$domain}lsearch*{/etc/virtual/domainowners}{$value}}"   quota = ${if exists{/etc/virtual/${domain}/quota}{${lookup{$local_part}lsearch*{/etc/virtual/${domain}/quota}{$value}{0}}}{0}}    ## vacation transport uservacation:   driver = autoreply   file = /etc/virtual/${domain}/reply/${local_part}.msg   from = "${local_part}@${domain}"   log = /etc/virtual/${domain}/reply/${local_part}.log   no_return_message   subject = "${if def:h_Subject: {Autoreply: ${quote:${escape:$h_Subject:}}} {I am on vacation}}"   text = "\ 	------                                                           ------\n\n\ 	This message was automatically generated by email software\n\ 	The delivery of your message has not been affected.\n\n\ 	------                                                           ------\n\n"   to = "${sender_address}"   user = mail   #once re-added May 16, 2008:   once = /etc/virtual/${domain}/reply/${local_part}.once   once_file_size = 100K   once_repeat = 2d  userautoreply:   driver = autoreply   bcc = ${lookup{${local_part}} lsearch {/etc/virtual/${domain}/autoresponder.conf}{$value}}   file = /etc/virtual/${domain}/reply/${local_part}.msg   from = "${local_part}@${domain}"   log = /etc/virtual/${domain}/reply/${local_part}.log   no_return_message   subject = "${if def:h_Subject: {Autoreply: ${quote:${escape:$h_Subject:}}} {Autoreply Message}}"   to = "${sender_address}"   user = mail   #once re-added May 16, 2008:   once = /etc/virtual/${domain}/reply/${local_part}.once   once_file_size = 100K   once_repeat = 2d   devnull:   driver = appendfile   file = /dev/null  # This transport is used for delivering messages over SMTP connections.  remote_smtp:   driver = smtp  # This transport is used for handling pipe deliveries generated by alias # or .forward files. If the pipe generates any standard output, it is returned # to the sender of the message as a delivery error. Set return_fail_output # instead of return_output if you want this to happen only when the pipe fails # to complete normally. You can set different transports for aliases and # forwards if you want to - see the references to address_pipe in the directors # section below.  address_pipe:   driver = pipe   return_output  virtual_address_pipe:   driver = pipe   group = nobody   return_output   user = "${lookup{$domain}lsearch* {/etc/virtual/domainowners}{$value}}"  # This transport is used for handling deliveries directly to files that are # generated by aliasing or forwarding.  address_file:   driver = appendfile   delivery_date_add   envelope_to_add   return_path_add  # This transport is used for handling autoreplies generated by the filtering # option of the forwardfile director.  address_reply:   driver = autoreply  ###################################################################### #                      RETRY CONFIGURATION                           # ######################################################################  # This single retry rule applies to all domains and all errors. It specifies # retries every 15 minutes for 2 hours, then increasing retry intervals, # starting at 1 hour and increasing each time by a factor of 1.5, up to 16 # hours, then retries every 8 hours until 4 days have passed since the first # failed delivery.  # Domain               Error       Retries # ------               -----       -------   begin retry  *                      *           F,2h,15m; G,16h,1h,1.5; F,4d,8h   # End of Exim 4 configuration

Udostępnij ten post


Link to postu
Udostępnij na innych stronach
Gość Marshall

Pocztę wysyłam z roundcube ale chodzi mi aby z panelu powiadom wszystkich użytkowników nie krzaczyło.

Udostępnij ten post


Link to postu
Udostępnij na innych stronach

DA po stronie przeglądarki działa w UTF-8 i w formularzu tak są kodowane wiadomości, i trzeba wykryć w exim, że wysłał to DA i dodać nagłówek.

 

Z tego co napisał @crazyluki dokładnie chodzi o fragment:

Podczas tworzenia wiadomości powitalnej (a także inne wiadomości wysyłane przez DA) wykorzystywane są 2 transporty "remote_smtp" (wysyłka maila poza serwer) i "virtual_localdelivery" (dostarczenie lokalne). Dodatkowo wykorzystuję informację, że DA wkleja swój nagłówek do wysyłanych wiadomości "X-DirectAdmin-Sender:"

Dzięki temu nagłówki z kodowaniem UTF-8 są doklejane tylko do wiadomości pochodzących z DA a nie do wszystkich.

Do obu transportów należy dodać

headers_add = "${if def:h_X-DirectAdmin-Sender:{Content-Type: text/plain; charset=utf-8\nContent-Transfer-Encoding: 8bit\n}}"

Udostępnij ten post


Link to postu
Udostępnij na innych stronach

Bądź aktywny! Zaloguj się lub utwórz konto

Tylko zarejestrowani użytkownicy mogą komentować zawartość tej strony

Utwórz konto

Zarejestruj nowe konto, to proste!

Zarejestruj nowe konto

Zaloguj się

Posiadasz własne konto? Użyj go!

Zaloguj się


×