ok
=== START OF INFORMATION SECTION === Device Model: ST3750528AS Serial Number: 6VP9PPW5 Firmware Version: CC44 User Capacity: 750,156,374,016 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 4 Local Time is: Fri Feb 1 17:42:19 2013 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 617) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 152) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103b) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 111 099 006 Pre-fail Always - 33354619 3 Spin_Up_Time 0x0003 095 095 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 36 5 Reallocated_Sector_Ct 0x0033 096 096 036 Pre-fail Always - 181 7 Seek_Error_Rate 0x000f 087 060 030 Pre-fail Always - 533419204 9 Power_On_Hours 0x0032 079 079 000 Old_age Always - 19160 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 36 183 Unknown_Attribute 0x0000 100 100 000 Old_age Offline - 0 184 Unknown_Attribute 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 073 073 000 Old_age Always - 27 188 Unknown_Attribute 0x0032 100 096 000 Old_age Always - 1125298667783 189 High_Fly_Writes 0x003a 098 098 000 Old_age Always - 2 190 Airflow_Temperature_Cel 0x0022 059 046 045 Old_age Always - 41 (Lifetime Min/Max 41/44) 194 Temperature_Celsius 0x0022 041 054 000 Old_age Always - 41 (0 23 0 0) 195 Hardware_ECC_Recovered 0x001a 042 015 000 Old_age Always - 33354619 197 Current_Pending_Sector 0x0012 096 096 000 Old_age Always - 178 198 Offline_Uncorrectable 0x0010 096 096 000 Old_age Offline - 178 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 184241212115753 241 Unknown_Attribute 0x0000 100 253 000 Old_age Offline - 3521132359 242 Unknown_Attribute 0x0000 100 253 000 Old_age Offline - 3166240442 SMART Error Log Version: 1 ATA Error Count: 24 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 24 occurred at disk power-on lifetime: 19140 hours (797 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 40 ff ff ff ef 00 8d+10:02:49.182 READ DMA EXT ec 00 00 00 00 00 a0 00 8d+10:02:49.133 IDENTIFY DEVICE ef 03 42 00 00 00 a0 00 8d+10:02:45.965 SET FEATURES [set transfer mode] ec 00 00 00 00 00 a0 00 8d+10:02:45.822 IDENTIFY DEVICE 25 00 40 ff ff ff ef 00 8d+10:02:42.937 READ DMA EXT Error 23 occurred at disk power-on lifetime: 19140 hours (797 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 40 ff ff ff ef 00 8d+10:02:42.937 READ DMA EXT ec 00 00 00 00 00 a0 00 8d+10:02:42.889 IDENTIFY DEVICE ef 03 42 00 00 00 a0 00 8d+10:02:42.817 SET FEATURES [set transfer mode] ec 00 00 00 00 00 a0 00 8d+10:02:42.650 IDENTIFY DEVICE 25 00 40 ff ff ff ef 00 8d+10:02:39.777 READ DMA EXT Error 22 occurred at disk power-on lifetime: 19140 hours (797 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 40 ff ff ff ef 00 8d+10:02:39.777 READ DMA EXT ec 00 00 00 00 00 a0 00 8d+10:02:39.768 IDENTIFY DEVICE ef 03 42 00 00 00 a0 00 8d+10:02:39.713 SET FEATURES [set transfer mode] ec 00 00 00 00 00 a0 00 8d+10:02:39.595 IDENTIFY DEVICE 25 00 40 ff ff ff ef 00 8d+10:02:36.710 READ DMA EXT Error 21 occurred at disk power-on lifetime: 19140 hours (797 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 40 ff ff ff ef 00 8d+10:02:36.710 READ DMA EXT 25 00 40 ff ff ff ef 00 8d+10:02:36.705 READ DMA EXT 25 00 40 ff ff ff ef 00 8d+10:02:36.138 READ DMA EXT 25 00 40 ff ff ff ef 00 8d+10:02:36.128 READ DMA EXT ea 00 00 ff ff ff af 00 8d+10:02:36.096 FLUSH CACHE EXIT Error 20 occurred at disk power-on lifetime: 19140 hours (797 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 40 ff ff ff ef 00 8d+10:02:32.637 READ DMA EXT ec 00 00 00 00 00 a0 00 8d+10:02:32.580 IDENTIFY DEVICE ef 03 42 00 00 00 a0 00 8d+10:02:32.460 SET FEATURES [set transfer mode] ec 00 00 00 00 00 a0 00 8d+10:02:32.318 IDENTIFY DEVICE 25 00 40 ff ff ff ef 00 8d+10:02:29.421 READ DMA EXT SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 8 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
